is the winstrol suppose to be milky white?
Answers:
0
A19 User profile Expert
Reply
Yes it is. Hope that helps. Don`t forget to vote. Thanks for the question.
1
Cyclone User profile Expert
Reply
Yes, and this is also typical of other water based steroid compounds, such as test suspension.
0
JD Cycle User profile Expert
Reply
Yes if it`s water based. Like cyclone said, common waterbased suspensions are also cloudy.
1
crazy Dan User profile Expert
Reply
Winstrol for injection is always milky and whitish my friend! It is suspended in water just like test suspension so you see tiny crystals floating in the solution. Try to draw it with a 22g needle and pin with a 25g. Pump plunger slowly and warm up the vial before drawing it up since it will cause some pip. In short, white milky color are precipitation (crystals) of the gear in solution and it`s perfectly normal. Good luck brother N don`t forget to vote.
0
RyanVogel User profile
Reply
Yes it is common don`t you worry
1
nickname_311 User profile Expert
Reply
Yes that is very common. I would start a little bit before injecting just Swirl It gently and be good with that and call it good good luck let us know how things go
—————————————————–
As with the other user this is so think cannot draw with 16G needle. Have tried running in hot water and nothing. Sort of a waste…
Answers:
1
Jason123 User profile
If you ever do get it pulled out just drink it. The crystals in that must be huge and would hurt like hell to inject.
1
Cyclone User profile Expert
Have you tried heating it a bit to try to dissolve the crystals?
1
Onyx User profile Expert
Try a bigger needle, as others have said try to drink it, many drink it with great results. I wish you luck and a successful cycle!
0
nickname_311 User profile Expert
There`s a lot of people that draw with a 12 gauge syringe. I would heated up swirl it around heat up some more to thin it out sounds awfully thick right now I draw with a 23 gauge syringe and it takes me about a minute to draw 1 cc maybe longer than that even just have patience when you`re drawing it out
1
JamesEarl User profile Expert
Try heating it up somewhat to thin up the solution, also try another method where you back load your syringe. Lastly you can drink winstrol because it is alpha alkylated 17 and so it survives first pass to your liver rendering the need to inject unnecessary. Not any other injectable steroid can be swallowed only the winstrol variety can. Good luck!
0
JohnSmith User profile
winny is normally suspended in water and as such it crystallizes extremely fast. Yes running under warm water is effective in breaking them up. Your best bet is to draw as fast as possible and inject as fast as possible. You may have to push and draw a few times before being able to clear it all.
0
Wolfcreek19 User profile
Berrio 18, just add 1 to 2 ML of Saline water or Bac water and shake it very well if it needs a little bit more fluid and one more ML of water. That should illuminate the clogging and dissolve the coagulation of the solution to not heat it up.
—————————————————–
This is so thick it will not break up or go into the syringe. is there any advice or instructions on how to do this or make this easier?
Answers:
0
JB205 User profile Expert
You can try slowly warming the vial under hot water and try drawing with a bigger gauge needle and using a smaller gauge to pin. 2
0
novadesert007 User profile
Run it under warm water and shake it up. It will break nicely. don`t pump in the one that is crystalized it will cause pip.
0
JMann User profile
Try warming the bottle either in your hands or under Luke warm water. You can also try using a bigger gauge needle to draw it out. Sometimes water base products crystallize, just need to warm the bottle, good luck.
0
Swolebro User profile
Slowly warm it in warm water and shake it up. It`s just cold and viscous. Before you inject you can rub it in your hands to warm it up to make injection easier.
0
nickname_464 User profile
You should be able to run it under warm water and see it thin out a bit. After that use a larger needle for drawing up just like you would with oil and then change to your normal needle and inject. Best of luck mate.
1
Dromeo User profile
Let the bottle sit in hot water for 10 minutes.